RoHS 2 (Directive 2011/65/EU) restricts ten hazardous substances in electrical and electronic equipment sold in the EU. Compliance is shown through a structured testing workflow, not a single measurement. This article covers product scope, sample preparation, XRF screening, GC-MS and ICP-MS confirmation, limit values, and compliance reporting.

Scope and Restricted Substances

RoHS 2 covers electrical and electronic equipment in eleven product categories. It extends the original directive to medical devices, monitoring instruments, and equipment not explicitly listed elsewhere. Since the 2015 amendment, the restricted list includes ten substances. These are lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls, polybrominated diphenyl ethers, and four phthalates: bis(2-ethylhexyl) phthalate, butyl benzyl phthalate, dibutyl phthalate, and diisobutyl phthalate. Each substance carries a maximum concentration value in homogeneous material. The first six are metals or element-based species measured as the element itself. The phthalates and brominated flame retardants are organic compounds. They require solvent extraction and chromatographic determination. The first step in a defensible test plan is to classify the product into a category and identify which homogeneous materials contain candidate analytes.

Sample Types and Preparation

Testing applies to homogeneous materials. A homogeneous material is any material that cannot be mechanically disjointed into different substances. Typical sample units include plastics and polymer housings, metal contacts and solder, cables, coatings, printed circuit boards, adhesives, and packaging components. Preparation begins with mechanical disassembly to isolate each homogeneous material, followed by size reduction. Polymers are cryo-milled or cut into pieces below roughly one millimeter to support dissolution. Metals are cleaned of surface contamination, drill-milled or filed, and degreased. For organic analysis, a weighed portion is extracted with a suitable organic solvent, commonly toluene or a hexane-acetone mixture. Ultrasonic extraction or Soxhlet extraction is used. For elemental analysis, digestion in concentrated acids converts the solid into a clear solution. This is often nitric acid with hydrogen peroxide in a microwave system. Contamination control tools and cross-contamination checks between samples form part of routine preparation discipline.

XRF Screening for Hazardous Elements

Energy-dispersive X-ray fluorescence spectrometry is the primary screening technique for lead, mercury, cadmium, chromium, and bromine in solid materials. The instrument irradiates the sample with X-rays and measures characteristic secondary emissions. It gives element concentrations within minutes without destroying the part. Screening is typically performed directly on disassembled components where the measurement spot is flat and of sufficient area. Small or curved parts are measured on milled homogenized powder pressed into a pellet. Results are interpreted against decision thresholds. Readings clearly below screening limits allow a pass judgment. Readings clearly above trigger confirmatory chemistry. Intermediate values are treated as inconclusive and sent for wet-chemical verification. Bromine by XRF is a surrogate indicator only, because the technique cannot distinguish restricted brominated flame retardants from other bromine sources. Phthalates are invisible to XRF and always require chromatographic methods. Screening reduces cost by concentrating confirmatory work on genuinely suspect materials.

GC-MS and ICP-MS Confirmation Methods

Confirmatory analysis splits the screening analytes into two method families. gas chromatography coupled with mass spectrometry handles the organic restricted substances. These are the four phthalates and, where bromine screening is inconclusive, polybrominated biphenyls and diphenyl ethers. Extracts are injected onto a non-polar or semi-polar capillary column. Compounds are separated by retention time, and the mass spectrometer confirms identity through characteristic ions. Quantification uses calibration curves built from reference standards. For elements, inductively coupled plasma mass spectrometry offers multi-element determination at trace levels on digested solutions. Atomic absorption spectroscopy and ICP optical emission are alternative confirmation platforms. Hexavalent chromium requires a separate approach, typically a colorimetric procedure with diphenylcarbazide reagent measured by UV-visible spectrophotometry. Total chromium alone cannot prove the valence state. Method quality is monitored through blanks, spiked recoveries, and certified reference materials where available.

Limit Values and Acceptance Criteria

The directive sets a maximum concentration value of 0.1 percent by weight in homogeneous material for lead, mercury, hexavalent chromium, polybrominated biphenyls, polybrominated diphenyl ethers, and each of the four phthalates. Cadmium is held to the stricter limit of 0.01 percent. Exemptions listed in the annexes permit higher levels for specific applications until they expire. An exceedance is therefore not automatically non-compliant until applicable exemptions are checked. Judgment is made per homogeneous material, not per component or per finished product. A single material above the limit renders the article non-compliant. Measurement uncertainty must be considered when results sit near the limit. Laboratories report results together with uncertainty so that pass or fail conclusions remain defensible. Reports typically state the screening judgment, the confirmatory values, and the acceptance decision against each limit.

Application

Scenarios and Compliance Reporting
RoHS testing supports several recurring scenarios in trade and manufacturing. New-product development uses screening data to qualify materials and supplier declarations before design freeze. Import and export shipments require test reports demonstrating conformity for EU customs and market surveillance authorities. Supplier audits rely on periodic retesting to verify that material compositions have not drifted after formulation or sourcing changes. Deliverables generally include a test report listing materials analyzed, methods applied, results with uncertainty, and limit comparisons, alongside supporting documentation such as declarations of conformity. Many manufacturers integrate RoHS data with REACH and packaging compliance into a single material file. The same sample preparation and elemental screening serve multiple regulatory programs. Retesting intervals follow internal risk policy. Common triggers include formulation changes, new suppliers, and revised exemption lists. A complete, traceable report reduces the likelihood of disputes during market surveillance checks.

Quick Answers

Frequently Asked Questions

01

If I dispute the RoHS2 compliance data, can A Closer Look at How the European Directive RoHS2 Impacts testing be repeated?

Yes. Retesting is available when results are questioned. It typically involves re-running XRF screening or confirming with GC-MS and ICP-MS on retained or newly submitted samples. Both parties can review the analytical records to resolve data disputes.

02

How long does RoHS2 testing take and how is the report delivered?

Turnaround depends on the methods required. XRF screening for hazardous elements is generally faster, while GC-MS and ICP-MS confirmation for restricted substances takes longer. Reports covering limit values and compliance conclusions are delivered in a documented format suitable for compliance reporting.

03

What

samples should I submit for RoHS2 restricted substance testing?
Sample types and preparation follow the scope of the directive: homogeneous materials from components, coatings, plastics, or metals. Samples should be separated into individual materials so XRF screening and subsequent confirmation methods yield accurate results against the limit values.

← Previous Article Seat belt testing
Next Article → Security door testing

Ready to Discuss Your Testing Needs?

Contact our team for a customized quote and expert consultation on your A Closer Look at How the European Directive RoHS2 Impacts testing requirements.

Contact Our Team
n n n n n n n n n n