Washington State's Children's Safe Products Act (CSPA) requires manufacturers of children's products sold in the state to report chemicals of high concern to children (CHCCs) to the Department of Ecology. This article walks through the full testing workflow: the regulated chemical list, sample preparation per CPSC methods, GC-MS phthalate analysis, ICP-MS heavy metal analysis, performance criteria, and compliance reporting.
Washington
State Children's Safe Products Act testing
The CSPA applies to products intended for children that are sold in Washington State. This includes toys, childcare articles, jewelry, and clothing. Manufacturers must report if their products contain a CHCC above practical quantitation limits. Ecology may then require chemical action plans or phase-outs. Testing therefore focuses on demonstrating whether listed substances are present and at what concentration. The scope overlaps partly with federal requirements under CPSIA. However, the state list is broader. It covers flame retardants, phthalates, bisphenols, certain metals, and other substances. A structured testing program aligned with the CHCC list lets manufacturers consolidate evidence for the state report. It also supports parallel obligations such as Children's Watch Testing, where watch components fall within children's product definitions.
Regulated
chemicals and reporting thresholds
The Washington Department of Ecology maintains the CHCC list and updates it periodically. Laboratories therefore screen against the current version before each campaign. Reporting applies when a listed chemical is present above the practical quantitation limit. This level is not a fixed statutory number. Each laboratory must document it through method validation. Key groups include ortho-phthalates such as DEHP, DBP, BBP, and DINP. They also include flame retardants — both organophosphate and brominated compounds — plus metals such as lead, cadmium, arsenic, and antimony, and phenolic compounds such as bisphenol A. The analytical plan should map each material in the product — plastics, coatings, textiles, metals, adhesives — to the chemical groups plausibly present. This targets the screening effort. The scoping step mirrors the material-by-material logic used in Toys & Children's Products Testing programs.
Sample
preparation and extraction — CPSC methods
Sample preparation follows CPSC test methods where available. These are chiefly CPSC-CH-C1001-09 for phthalate determination in plastics and CPSC-CH-E1001-08 and related methods for total lead in paints, substrates, and metal components. For phthalates, the accessible plastic or polymeric part is ground or cut into small pieces to increase surface area. It is then dissolved or swollen in tetrahydrofuran or dichloromethane and extracted with hexane, often with sonication. An internal standard is added before extraction so matrix losses are compensated quantitatively. For metals, paint films are scraped from the substrate. They are digested in nitric acid with hydrogen peroxide under heated conditions and diluted to volume. Homogeneity matters: multi-component products are separated into discrete material samples before digestion or extraction. A blended result from unlike materials cannot support a material-level report.
Phthalates
and heavy metals analysis — GC-MS and ICP-MS
Phthalate extracts are analyzed by gas chromatography with mass spectrometric detection. The method uses a non-polar or mid-polarity capillary column and selected-ion monitoring for each target compound plus isotopically labeled internal standards. Calibration is built with matrix-matched or solvent standards across the working range. Individual phthalates are quantified separately, since the regulation lists them individually. Heavy metal digests are measured by inductively coupled plasma mass spectrometry, which offers multi-element capability and low background. ICP optical emission spectrometry can be used for higher-concentration screening. Quality controls include calibration verification and continuing calibration checks. They also include method blanks, duplicate digestions, and certified reference materials where available. Contamination control deserves attention: phthalates are ubiquitous in laboratory environments. Glassware is therefore baked, solvents are verified blank-clean, and plastic labware is avoided throughout the phthalate workflow.
Method
performance — detection limits and recovery
Before results can support a CSPA report, the laboratory must show that each method meets defined performance criteria. Method detection limits are established through replicate analysis of low-level fortified matrix. Reporting limits are set above the detection limit with an adequate margin of confidence. Recovery studies — typically spike-and-recovery tests on real product matrices — verify that extraction and digestion release the target analytes. Acceptance ranges, such as those cited in the CPSC methods, are used as benchmarks. Precision is assessed through duplicate preparations, and blank results confirm the absence of background contribution. Results between the detection limit and reporting limit are reported as detected but not quantifiable. Comparable performance verification applies to adjacent programs. Examples include Damp Heat Steady-State Test work or Solid-State Relay (SSR) Testing in electrical product evaluations, where stability and repeatability criteria likewise anchor the validity of reported parameters.
Compliance
reporting and co-testable parameters
Once analytical data are available, manufacturers file a report with the Department of Ecology. The report identifies the product, the CHCCs present, their concentration ranges, and the intended function of each chemical — whether intentional or contaminant. Reported concentrations are typically presented in ranges. This reduces the burden of exact quantification while still informing the agency. Testing can be consolidated: the same sample preparation used for phthalates and lead can be extended to screen other CHCC groups where methods allow. CCHA sampling frequently runs in parallel with CPSIA, EU toy, or RoHS-type obligations. Co-testing reduces total sample consumption and avoids conflicting results between separately commissioned studies. Laboratory documentation — chain of custody, method references, and validation summaries — should be retained. Ecology may request supporting evidence after a report is filed.
Frequently Asked Questions
What
products and materials fall under the Deadline Approaching: Washington State Children's Safe Products Act testing requirements?
The Washington State Children's Safe Products Act applies to children's products made or offered for sale in Washington State. Regulated chemicals are assessed across defined material categories, including plastics, metals, textiles, and coatings. Reporting is triggered when chemicals exceed applicable thresholds.
What
should a Washington State Children's Safe Products Act compliance report contain?
Reports should identify the product and tested materials. They should list regulated chemicals analyzed, describe the CPSC-based sample preparation and extraction methods used, and present GC-MS and ICP-MS analytical results against reporting thresholds. They should also document method performance, including detection limits and recovery data.
How is the Washington State Children's Safe Products Act report submitted, and what are key communication points?
Submission involves providing the completed compliance report with supporting analytical data and identifying a responsible contact for follow-up. Key communication points include confirming applicable chemical scope, clarifying sample material designations, and aligning on co-testable parameters before reporting to streamline the process.