Titanium Rockwell hardness testing uses the Rockwell B scale (1.588 mm tungsten carbide ball, 980.7 N force) for commercially pure titanium and annealed alpha alloys, and Rockwell C or A scales with a diamond cone for harder alpha-beta, beta, or surface-hardened grades. It is a fast indentation method for incoming inspection, heat-treatment verification, and batch consistency control.
Titanium Rockwell hardness testing
The Rockwell method measures hardness by pressing an indenter into the specimen. It first applies a defined preliminary force, then a total test force. The hardness value comes from the difference in indentation depth before and after force removal. Two indenter types are used: a diamond cone for harder conditions and tungsten carbide balls for softer ones. Wrought titanium products generally fall in a mid-range hardness band. Ball indenters on the Rockwell B scale are therefore the routine choice, while the diamond cone on Rockwell C or A scales suits harder alloy grades or hardened surfaces. The method needs only one surface with reasonable finish and gives a direct dial or digital readout. This makes it suitable for production-floor inspection as well as laboratory verification.
Scales and principle selection
Scale selection depends on the expected hardness band of the specific titanium grade. Commercially pure titanium and annealed alpha alloys are typically tested on the Rockwell B scale. This uses a 1.588 mm tungsten carbide ball with a 980.7 N total force. Higher-strength alpha-beta and beta alloys, or parts with nitrided or diffusion-hardened surfaces, may call for the Rockwell C or Rockwell A scale with a diamond cone indenter. The chosen scale must place the reading within its valid measuring range and avoid indenter damage. When the material grade is unknown, a trial indentation on the A scale can help locate the correct range before committing to a full test pattern. Surface-hardened titanium with thin cases may instead require a superficial Rockwell scale with lower forces.
Sample preparation requirements
The test surface must be flat, smooth, and free of oxide scale, decarburized layer, grease, and marking ink, because surface faults shift the indentation depth reading. Grinding with progressively finer abrasive paper, followed where necessary by light polishing, is normally sufficient. The finish should be smooth enough that the indentation boundary can be read without ambiguity. Specimens must be rigidly supported so that no movement or elastic sinking occurs during loading. The underside should be clean and flat against the anvil. Curved surfaces such as bars and tubes require a flat machined spot or correction for curvature, since a convex surface artificially lowers the measured hardness. Thickness matters as well: the specimen must be at least ten times the permanent indentation depth. No bulging or marking shall appear on the reverse face after testing.
Stepwise testing procedure
Begin by verifying the machine condition. Check the indenter for damage, confirm the correct anvil for the specimen geometry, and allow the instrument to stabilize at room temperature. Verify machine accuracy with certified reference blocks at the chosen scale before daily use. Place the specimen on the anvil, apply the preliminary force, and confirm the datum is set. Apply the total test force and hold it for the specified dwell time, typically two to eight seconds depending on material response. Then release to the preliminary force and read the hardness value. Record the scale designation together with the numeric value. Move the specimen so that successive indentations keep the required spacing. The center-to-center distance between indentations shall be at least three times the indentation diameter. The distance from an indentation center to the specimen edge shall be at least two and a half times the diameter. Discard readings from any indentation placed on an edge or prior mark.
Repeatability and result judgment
The reported hardness of a specimen should be the arithmetic mean of at least three to five valid indentations, with the scatter recorded alongside the average. Excessive scatter usually points to preparation faults, unstable support, microstructural inhomogeneity, or a scale chosen near its limit. Judging acceptance requires a stated criterion agreed befOre testing. This may be a specified hardness band in the material specification or a minimum value in the purchase order. Converted values from Rockwell to Vickers or tensile strength must be treated as reference only, because conversion tables carry uncertainty and titanium alloys do not always follow generic conversion curves. If readings fall close to a specification limit, the tester should add indentations and review preparation, anvil support, and dwell-time consistency before making a final judgment.
Applicable standards and applications
Rockwell hardness testing of titanium follows the general metallic Rockwell method standards commonly used in laboratories, together with the specific material standards that assign hardness limits to each titanium grade. These documents define indenter geometry, force tolerances, dwell conditions, verification procedures with reference blocks, and reporting requirements. Typical applications include incoming inspection of titanium bar, plate, and forged stock; verification of annealed or solution-treated and aged condition; screening of welded joints where the base metal hardness is checked; and routine quality control in aerospace, medical device, chemical plant, and marine hardware manufacturing. For finished components with strict surface integrity requirements, Rockwell results are often cross-checked with a microindentation method on a metallographic section.
Frequently Asked Questions
Which
products are suitable for Rockwell hardness testing?
Wrought titanium bar, plate, sheet, forgings, and many finished machined parts can be tested by the Rockwell method, provided the sample meets the thickness and flatness requirements described above. Thin foil, coatings, and very thin hardened cases are not suitable for the standard scales and require superficial or microindentation methods instead.
What information does a report contain?
A typical report identifies the material and product form, the test scale and indenter type, the number of valid indentations, individual readings, the mean value, the testing temperature, and the standards followed. Any deviations in preparation or dwell time, and the acceptance criterion when one is agreed, are also stated so that users can judge conformity accordingly.
How should a client prepare samples and communicate before submitting for Rockwell testing?
Clients should specify the titanium grade and product form, the expected hardness range or specification limit if known, and whether the result is for incoming inspection or process verification. Sample size, test location on the part, and any restriction on indentation marks are the key points to confirm with the laboratory before testing begins.